Importance Of Calibration Instruments In Factories

By: Low Jeremy

Machines need to be calibrated regularly so these will be able function properly. A licensed engineer or mechanic is the only one qualified to perform such tests and the length of time it takes to inspect one unit could take hours depending on how complex or sophisticated it is.

If the machines being checked are in large factory such as one that produces cars, teams are dispatched to conduct the calibration. In most cases, this is done every six months. The only difference is that the people who will do this will go to the plant unlike a car owner who will have to drive the vehicle to the shop.

Is there any difference between a machine and a car when it comes to calibration? Yes in terms of the instruments used to conduct such tests. Large ones like those in the factory have to be dismantled and hand held instruments such as frequency counters, multimeters, network analyzers, oscilloscopes, power supplies, spectrum analyzers and RF power meters are used throughout the tests.

Automobiles on the other hand are tested using computers and some similar instruments that will be finished much faster than those in the factory so the owner can drive off when this is done. If a problem has been found, the specialist will recommend that the machine should not be used first until a replacement part has arrived. But in minor cases, a simple adjustment will do the trick making it up and running again.

But the use of calibration instruments is not only done in factories. These are also done in laboratories to make sure the machines used are able to perform to what it was designed to do. The National Institute of Standards and Technology is responsible for setting the regulations making this all possible. After all, safety begins by those who are designing the prototype until the new product is launched into the market. This will ensure that defects can be avoided and recalls are not necessary since this will cost the company a lot of money.

Anything that uses machines will have to be calibrated at one point or another to ensure these are performing well as though these were good as new. The plant may have a crew to do this or a contractor can be called in to perform such services which is really up to those in charge of keeping the place running.

Manufacturing, industrial, and even chemigation processes, benefit from the use of a system that includes the use of a calibration column. A system that includes a calibration column in its process allows you to easily determine the flow rate of liquids that are pumped from your manufacturing, industrial or chemigation processes.

A calibration column is usually made out of clear PVC with industry grade graduations that measure things such as milliliters per minute and gallons per hour. You can install one calibration column for each pump set to measure pump flow rates.

A calibration column is a very important tool. In industrial and chemical processes, precision is of extreme importance and the calibration column assures you of that. All kinds of systems that include processes where liquids are pumped will need the reliability of a calibration column. Pumping system solutions that include calibration columns vary from each other depending on what purpose it will serve.

For instance, if industrial chemicals will be introduced into the system, it is important that the graduation marks on the calibration column are protected from chemical corrosion for it to continue to maintain its integrity. If on the other hand, your pumping systems require the strict regulation of flow rates, you need a system with a calibration column that is connected to an emergency release valve to be able to minimize total risk.

There are many dependable and reliable pump system solutions provider in the market that can supply the right kind of system with the right kind of calibration column for your needs and requirements. To help you along on your search, you might want to check out some industrial grade systems that include the use of a calibration column for your pumping processes.

Cole-ParmerCole-Parmer is an instrument company that distributes various industrial fluid handling products including gear pump systems that come with a calibration column. The company has been around since 1955 and has become one of the largest distributor of instrumentation products that deliver the right solutions to your business. You can check them out online at coleparmer.comKofloKoflo Corporation begun as a family endeavor in the early 1980s and since then has grown in scope and size.

They pride themselves in being able and willing to adapt to their customers' needs and requirements to be able to provide to perfect fit in terms of industrial instrumentation solutions. They offer different pumping systems that include calibration columns. You can get a quote from them today at their website-- koflo.com

Top Searches on
Electronics
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 
 • 

» More on Electronics
 



Share this article :
Click to see more related articles