IT Hardwares


eg: UK or Brides UK or Classical Art or Buy Music or Spirituality

Business & Money

Technology

Women

Health

Education

Family

Travel

Cars

Entertainment

Featured Sites

Canon Printer Error Code

View:

Have you ever encountered a printer error code while using your Brother multifunction printer? Chances are that you have. It is not that the Brother multifunction printer is an inferior machine; in fact, it is one of the best multifunction printers out there. But just like any machine, it can bog down. And when it does, a printer error code might pop up on your computer screen or on the LCD control panel of the printer.

What are the common printer error codes of Brother multifunction printers and how can we fix them? Here is a list of these common printer error codes.

? Error Code S05. A printer error code like this happens when the transfer of data via the parallel port is not going smoothly. Just reset your printer to get it going again.

? Error Code E50. This printer error code flashes when the fuser unit of your Brother multifunction printer gets damaged. When this happens, it is a signal that you must replace your printer's fuser unit.

? Error Code E51. When the printer's laser beam, lid or mirrors are not placed in their appropriate positions, it results in this printer error code. Please check if ink cartridges and everything in your printer is where it should be before you start using it again.

? Black pages. Sometimes, the message ?Black pages" can flash on the screen, or a black page is actually being printed out. In this case, you would need to take your printer to a service center and replace its jumper wires and diodes.

? Check paper path. When this message shows up, it means that your Brother printer has a dirty or misaligned eject roller. Clean it or straighten it up, whichever is necessary, and then try printing again.

? Poor quality of copy. When the output of your Brother multifunction printer, be it the printout or the fax, is smudgy, it could be because the scanning mirrors or the glass is dirty. Clean them up if they are. However, if these are clean, then the problem could be your printer's camera. You can try out unplugging your printer for a few hours, but if the problem persists, you may have to go to a service center to get your printer's camera replaced.

Canon Printer Error Code

Error code 22: Out of paper

This could indicate either a paper jam or a shortage of paper in your IBM and Lexmark printer. Make sure there is sufficient paper loaded into the paper tray and also check if there are any sediments collected along the path of paper. Check to see if the sensor flag for input is broken or not and also ensure the system boards and cable 2 is not defective.

Error code 31: Paper change needed

This means that your Lexmark and IBM printer has a different paper size configuration from what's needed in the software. Make sure to change the paper settings to adjust the size. Also check the printer software setup for any issues as well as the system board for any fault.

Error codes 41 and 43: Font related

These error codes usually indicate that the particular font needed is not available in the Lexmark and IBM printer. This could signal a faulty font card or a fault inside the system board. It might also mean that the font card had been removed while the power was switched on. If the font card is defective make sure to get a new one.

Error code 54: serial error

This error code indicates that the settings for the serial configuration between your computer and your printer are different. Make sure the communication cable, I/O cable and system boards are not damaged or improperly connected.

Error code 89: Overloaded output tray

This error code implies that your output tray is completely full. Make sure to take out paper from the output tray. You also need to check the operability of the respective flags. You can also try replacing the photo sensor for the card.

Error code 9920: Fuser not as per temperature

For this error code you need to monitor the resistance on the fuser as well as on the thermo fuse, lamp and the thermistor. There could also be a problem with low voltage. Check if there is continuity in the cable 1 of the system as well as inside the power cable inside the fuser.

Error code 970: improper turning on the fan

This means that the fan inside the Lexmark and IBM printer is not turning on. You could try to reseat the cables that lie between the system board and the fan. Also try resetting the printer.

Error code 24: Incorrect manual feed

This error code could come up due to a variety of reasons. If you are trying to put the paper inside manual feed at the same time the printer is taking off paper from the paper tray then the error could occur. Make sure not to put paper inside manual feed until and unless it has been explicitly requested.

More Articles from

Computer Hardware Guide

Related Articles
Author
Most Popular

•	Canon Compatible Printer Cartridges, by Nitzan Daphna
•	Canon Compatible Printer Ink, by Carla Weaffer
•	Canon Pixma Ip1800 Inkjet Printer, by Alan Wilson
•	Canon Pixma Mp970 Photo All In One Printer, by Jacob Georgeson
•	Canon Pixma Photo Printer Reviews, by Christy Berger

James Kara Murat has sinced written about articles on various topics from Computers and The Internet, computers and the internet and Marine Corps. James Kara Murat the contributor of compatible ink cartridges. More information on the subject is at. James Kara Murat's top article generates over 60500 views. Bookmark James Kara Murat to your Favourites.

Building A Dream Home
It will make the project easier, less expensive, and will help ensure that your new home is a dream come true, and not a nightmare